User Contributed MET/CAL PROCEDURE ============================================================================= INSTRUMENT: PM 5138A (Performance) Ver 1.0 DATE: 05-Jun-94 AUTHOR: User Contributed REVISION: 1.0 ADJUSTMENT THRESHOLD: 70% NUMBER OF TESTS: 1 NUMBER OF LINES: 86 CONFIGURATION: HP 436A CONFIGURATION: Philips PM 3365A CONFIGURATION: Philips PM 5191 CONFIGURATION: Philips PM 6654C CONFIGURATION: HP 8568A CONFIGURATION: Fluke 8842A CONFIGURATION: HP 8901A ============================================================================= STEP FSC RANGE NOMINAL TOLERANCE MOD1 MOD2 3 4 CON * 컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� * Source: Operating Manual PM 5138A P/N: 4822 872 10113 @940312 * 컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� * TUR Configuration: HP 436A, Philips PM 3365A, Philips PM 5191 * Philips PM 6654C, HP 8568A, Fluke 8842A, HP 8901A * 컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� * When the T.U.R. is < 2:1, the source instrument, e.g. 5700A, must be * characterized and appropriate corrections entered in the correction file * (e.g. 5700.COR). Where T.U.R.'s are > 2:1 but < 4:1, the test tolerance * is reduced by root sum square (rss) techniques. * 컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� * This procedure is not executable in MET/CAL versions below ver. 2.00 * 컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� * Fluke makes no warranty, expressed or implied, as to the fitness or * useability of this procedure. * 컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� * The following subprocedures are called from this main procedure: * Sub PM 5138A: 5.4.1 - 5.4.4.4 RS232 * Sub PM 5138A: 5.4.5 - 5.4.6.1 RS232 * Sub PM 5138A: 5.4.6.2 - 5.4.8.3 RS232 * Sub PM 5138A: 5.4.8.4 - 5.4.10 RS232 * Sub PM 5138A: 5.4.1 - 5.4.4.4 IEEE * Sub PM 5138A: 5.4.5 - 5.4.6.1 IEEE * Sub PM 5138A: 5.4.6.2 - 5.4.8.3 IEEE * Sub PM 5138A: 5.4.8.4 - 5.4.10 IEEE * Sub FM RESIDUAL Measurement * Sub AM Measurement * Sub FM Measurement * Sub THD Measurement * Sub PM 51xx RISETIME * Sub PM 51xx FALLTIME * 컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� 1.001 ASK- R P F W 1.002 HEAD INTRODUCTION 1.003 DISP This procedure is intended to: 1.003 DISP - Check the instrument's specification. 1.003 DISP - Check the nessesity for re-calibration. 1.003 DISP 1.003 DISP NOTE: UUT Requires 30 Minutes warmup before testing. 1.003 DISP 1.004 DISP If the UUT does not have a remote interface, install 1.004 DISP the PM513x IEEE test interface. 1.004 DISP 1.005 OPBR Does the UUT have a IEEE option. 1.006 JMPT 1.013 1.007 DISP Set the UUT RS232 interface for: 1.007 DISP Baud: 9600 1.007 DISP Parity: None 1.007 DISP Bits: 8 1.007 DISP Parity: 1 1.007 DISP XON/XOFF: Off 1.008 CALL Sub PM 5138A: 5.4.1 - 5.4.4.4 RS232 1.009 CALL Sub PM 5138A: 5.4.5 - 5.4.6.1 RS232 1.010 CALL Sub PM 5138A: 5.4.6.2 - 5.4.8.3 RS232 1.011 CALL Sub PM 5138A: 5.4.8.4 - 5.4.10 RS232 1.012 END 1.013 CALL Sub PM 5138A: 5.4.1 - 5.4.4.4 IEEE 1.014 CALL Sub PM 5138A: 5.4.5 - 5.4.6.1 IEEE 1.015 CALL Sub PM 5138A: 5.4.6.2 - 5.4.8.3 IEEE 1.016 CALL Sub PM 5138A: 5.4.8.4 - 5.4.10 IEEE 1.017 END 1.018 IEEE [@436] 1.019 IEEE [@3365] 1.020 IEEE [@5191] 1.021 IEEE [@6654] 1.022 IEEE [@8568] 1.023 IEEE [@8842] 1.024 IEEE [@8901]